 |
NEEDLE BEARING TOOLING
UPRIGHT PRESS
STAGE 1
|
|
UPRIGHT PRESS
|
| 1P1 |
FORD AND DELCO ARMATURE SHAFT INSTALLATION SLEEVE |
| 1P2 |
SMALL DELCO ARMATURE SHAFT INSTALLATION SLEEVE |
| 1P4 |
THIN FORK FOR SPACING ALL ALTERNATOR SLIP RINGS |
| 1P5 |
SMOOTH SURFACE PUSH PAD |
| 1P6 |
THICK FORK FOR SPACING ALL ALTERNATOR SLIP RINGS |
| 1P7 |
SLEEVE FOR SPACING ROTOR SHAFTS IN DELCO ALTERNATORS |
| 1P8 |
SLEEVE FOR SPACING ROTOR SHAFTS IN CHRYSLER ALTERNATORS |
| 1P9 |
SLEEVE FOR SPACING ROTOR SHAFTS IN FORD ALTERNATORS |
| 1P10 |
STARTER ARMATURE SLEEVE STAND HOLDER |
|
ROTOR: SHAFT CHANGING TOOLING
UPRIGHT PRESS
STAGE 2
|
 |
1P11 |
STARTER ARMATURE STAND FOR REMOVING SHAFTS |
| 1P12A |
STARTER SHAFT INSTALLATION GAUGE AND TOOL (½" HOLE) |
| 1P12B |
STARTER SHAFT INSTALLATION GAUGE AND TOOL (5/8" HOLE) |
| 1P13S |
CHUCK FOR RAM (SPECIFY THREAD SIZE (1 ¼"-12) OR (1 ½"-12)) |
| 1P14 |
STAND FOR ALTERNATOR AND STARTER SHAFT REMOVING |
| 1P15 |
ALTERNATOR AND STARTER PUSH OUT SHAFT |
| 1P20 |
DELCO 5 MT. STARTER ARMATURE SHAFT INSTALLATION RING |
| 1P21 |
NEEDLE BEARING SPRING LOADED INSTALLATION STAND |
| 1P22 |
NEEDLE BEARING REMOVING STAND |
| 1P25 |
NEEDLE BEARING INSTALLATION CHUCK EXTENSION TOOL |
 |
LAYDOWN PULLY, BEARING END
PLATE REMOVAL TOOLING
LAYDOWN PRESS
STAGE 3
|
1P28 |
NEEDLE BEARING CHUCK EXT. REMOVING TOOL |
| 1P30A |
CHUCK FOR RAM (SPECIFY TOOL SIZE (1 ¼"-12) OR (1 ½"-12)) |
| 1P31 |
STAND (BOLTED ON PRESS FOR ALTERNATORS) |
| 1P33 |
FORD 4" ARMATURE RING |
| |
LAY DOWN PRESS
|
| 2P1 |
SM. BEARING REMOVER PLATES (1 1/16" HOLE) |
| 2P2 |
SM. PULLEY PULLER PLATES (2" HOLE) |
| 2P3 |
MED. PULLEY PULLER PLATES (2 ½" HOLE) |
| 2P4 |
LRG. PULLEY PULLER PLATES (3' HOLE) |
| 2P5 |
CLAMP FOR BROKEN BEARING PULLER |
|
MT 40
|
 |
2P6 |
ALTERNATOR AND PLATE PULLER |
| 2P7 |
BROKEN BEARING PULLER (COMPLETE) |
| 2P7B |
(2) LONG SHOULDER BOLTS FOR 2P7, 2P8, 2P9 |
| 2P7B2 |
(6) ALLEN HEAD SCREWS FOR HOLDING JAWS ON |
| 2P8 |
PULLEY PULLER WITH HUBS (COMPLETE) |
| 2P9 |
203 BEARING PULLER (COMPLETE) |
| 2P10 |
CHUCK SPECIFY THREAD SIZE (1 ¼"-12) OR (1 ½"-12) |
| 2P11 |
PUSH ROD EXT. FOR 2P1 PLATES |
| 2P12 |
PUSH ROD |
| |
|
